AG亚洲

 
Close
(0) Shopping cart
You have no items in your shopping cart.
Shopping Categories
    Filters
    Preferences
    Search

    3 hp VFD, Single Phase to Three Phase VFD

    5 out of 5 based on 2 reviews | Write a review
    $238.14
    Low price 3hp VFD, convert 220V/230V/240V 1 phase to 3 phase, 10amps, RS485 enabled, shipping weight 3kg, manufacturer direct sale.
    SKU: GK3000-2S0022
    Free Shipping Worldwide
    Delivery date: 6-20 days

    3hp variable frequency drive, 2.2kW, single phase 220V-240V to three phase VFD, 10 amps.

    Specification:

    Basics Model GK3000-2S0022
    Capacity 3 hp (2.2 kW)
    Shipping weight 3 kg
    Dimension 184*98*135 mm
    I/O Feature Rated current 10 A
    Input voltage 1 phase 220~240V AC ±15%
    Input frequency 50Hz/ 60Hz
    Output voltage 3 phase AC 0~input voltage
    Output frequency 0.00~400.00Hz
    Over load capacity 150% of rated current for 1 minute, 180% of rated current for 3 seconds
    Control Feature Control mode V/F control;
    Sensorless vector control;
    Communication RS485
    Speed regulation 1:100
    Start torque 150% of rating torque at 1 Hz
    Speed control accuracy ≤±0.5% of rating synchronous speed
    Frequency precision Digital setting: max frequency x± 0.01%;
    Analog setting: max frequency x± 0.2%
    Frequency resolution Analog setting: 0.1% of max frequency;
    Digital setting: 0.01Hz
    Torque boost Automatic torque boost, manual torque boost 0.1%~30.0%
    Interior PID controller Be convenient to make closed-loop system
    Automatic energy save running Optimize V/F curve automatically based on the load to realize power save running
    Automatic voltage regulation (AVR) Can keep constant output voltage when power source voltage varies.
    Automatic current limiting Limit running current automatically to avoid frequent over-current which will cause trip
    Environment Enclosure rating IP 20
    Temperature –10℃~ +40℃; VFD will be derated if ambient temperature exceed 40℃; each rise 1℃, the derate will be 5%
    Humidity 5%-95%, without condensation
    Altitude ≤1000m; VFD will be derated if above 1000m
    Impingement and oscillation Normal running:<5.9m/s2 (0.6g); Transportation:<15m/s2 (1.5g)
    Store environment –20℃~ +60℃; no dust, no corrosive gas, no direct sunlight

    Tips: Variable frequency drive overcurrent
    Overcurrent is the most frequent alarm phenomenon of VFD.

    AG亚洲A. Phenomenon

    1. When restarting, VFD trips once speed up. This is a very serious phenomenon of overcurrent. The main reasons are: Load short circuit, mechanical parts stuck, inverter module damaged, and smaller motor torque and so on.
    2. Tripping after power on. This phenomenon cannot be reset. The main reasons are: Module broken, bad driving circuit, and bad current detection circuit.
    3. The tripping is not happening when restart but when accelerating, the main reasons are: Acceleration time setting is too short, current upper limit setting is too small, and the torque compensation (V/F) setting is too high.

    B. Maintenance examples

    1. The VFD displays "OC" once starting.
      Open the cover and don't find any signs of burn out. Online measure IGBT finds no problems. In order to further determine the problem, disassemble the IGBT and measure the seven high-power transistors, the opening and closing are good. When measuring the upper half of the bridge drive circuit, find a circuit is obviously different with the other two. After careful inspection, find an optocoupler A3120 output pin and negative power supply short circuit. Replace it and test again, three circuits are the same. Finally install IGBT and everything running well.
    2. A 3 hp VFD displays "OC" and cannot be reset.
      First check the inverter module but don't find the problem. Second, check the drive circuit and find no abnormal phenomenon. It is estimated that the problem is not here, and may be in the part of over-current signal processing. Remove the circuit sensor and then power on showing everything is normal, so the sensor has been broken. After replaced with a new sensor, the on-load experiment shows everything normal.
    Existing reviews of 3 hp VFD, Single Phase to Three Phase VFD
    Works great, excellent vfd.
    I received my VFD in a few days and it took me a while to set up the power, but now it is up and running. This 3 hp VFD is better than described, I waited to review till I had it fully installed and cutting. Manual is very well written, and each word and diagram is important to study.
    From: David | Date: 05/09/2018
    Was this review helpful? Yes No (0/0)
    Can I use your 3 hp Single Phase to Three Phase VFD for my saw
    Hi,
    my table saw has a 3 phase Baldor 3HP motor and I need a drive. Can I use your 2.2 kW variable frequency drive for it. 10A is good. The saw runs on one speed only will the VFD be a problem?
    From: Andy | Date: 10/08/2020
    Was this review helpful? Yes No (0/0)
    ATO Responded
    If your motor is 3-phase, 220/230V, and your supply voltage is 1-phase, 220/230V, then recommended 5 hp (4 kW) 1 phase to 3 phase VFD. Buy it on: pgyt681.cn/5hp-vfd
    Write your review for 3 hp VFD, Single Phase to Three Phase VFD
    • Only registered users can write reviews
    • Bad
    • Excellent
    Customers who bought this item also bought

    Strain Gauge Load Cell, S type, 5kg/20kg/30kg/500kg to 7 ton

    $82.59
    SKU: ATO-LC-S02
    S type load cell can bear both tension and pressure, with overload protection device, good output symmetry, high accuracy, compact structure and complete specifications. Strain gauge load cell can be applied for batching scale, electronic-mechanical scale, crane scales, automatic weighing instrument and other force value measurement and control.

    15 hp VFD, Single Phase to Three Phase VFD

    $1,453.95
    SKU: GK3000-2S0110G
    Affordable 15 hp single phase VFD, 1 phase 220-240v 50Hz/60Hz input and 3 phase 220v 230v 240v output, running three phase motor on single phase household power supply.

    5 hp VFD, Single Phase to Three Phase VFD

    $294.31
    SKU: GK3000-2S0037
    5hp variable frequency drive, single phase to three phase VFD, 17amps, RS485 enabled, shipping weight 4kg, manufacturer direct sale.

    1 hp VFD, Single Phase to Three Phase VFD

    $159.32
    SKU: GK3000-2S0007
    1 hp VFD, convert single phase to three phase for AC motor speed controls, IP20, RS485 enabled, shipping weight 2kg, manufacturer direct sale.